Monday, May 25, 2009

Never True

My DuraAce WH-7850-CL wheels are really light and have smooth bearings, but the front wheel gets knocked out of true easily. I think I could hit it on the side with a Q-tip and make it wobble. It's likely that it was rubbing the brakes at Westlake last week. No wonder I wore out so quickly and felt so bad the next day! I think I rode a couple of laps with the front brake on!

The rear wheel is very stable. There just aren't enough spokes in that front wheel for our rough Northeast Ohio roads and my heavy body. I'll keep riding with it at Leroy and on training rides until I get more confidence in its ability to survive before I race with it.

I'll swap it out for one of the slightly heavier bladed spoke wheels in my stable for tackling the concrete at Westlake. The DA wheel is 1 kg with skewer, tube, and tire. The old wheel is another Shimano wheel with straight pull spokes and weighs in at 1.13 kg, only a quarter pound heavier 0.1% of the total bike+rider weight, but can take a lot more abuse. In fact, I ride a set of those on my cyclocross bike.

Thursday, May 21, 2009

Finally, no wind at Leroy!

I was feeling really flat all day, but was looking forward to the Leroy TT, so I loaded up the Element and drove up to the fire station in the afternoon. The wind was strong out of the south when I was out doing my warm up cruise around the course. I felt like I was riding through glue. 

In the parking lot as we were staging to do our timed runs, I spun the front wheel and noticed it was hitting the brake pad. I was able to adjust the brakes so the wheel spun through cleanly a few minutes before I was due to roll. That was a relief. Also, the wind had completely died down, so I'd be able to get a time that wasn't influenced by the direction and speed of the wind, so I started to feel pretty good and motivated.

I was aiming to shave some time off last week by picking up the pace in a few strategic spots on the course--on the second half of the climb, and just before the turn around. Otherwise, I followed the routine I established over the prior weeks. I keep the pace relatively easy from the start, and then gradually accelerate toward the corner.

I planned to take a little breather through the corner, then ramp up the power all the way through the climb. Like last week, I made it up the first part of the climb at good pace but wilted on the second part until the summit, where I managed a decent sprint. My oxygen starved brain managed to keep the legs going to the turn around.

I kept the pace up on the decent, though not as fast as I could go. So I eased off a little bit until the 2 miles to go mark, then I started to bang the pedals all the way through the finish. I shaved more time off last week and managed a 20:37. I'm aiming for sub 20 minutes next week.

Here's some stats:

First two miles: 369 Watts Average. 22.4 mph average. 25.5 max.
To top of climb: 332 Watts Average. 19 mph avg. 7.9 mph minimum speed (top of hill)
Back down the hill: 331 Watts average. 24.5 mph average.
Last two miles: 389 Watts average. 23.9 mph average, 29.9 max.

Total time 20:37, Avg. power 358 Watts. Average speed 22.4 mph.






Wednesday, May 20, 2009

Training Tweaks

I'm in the no-man's land of my season. I'm trying to make a jump in fitness, but am not fit enough to be competitive in harder races. I'm able to sustain good power for long intervals, but I don't have the endurance to do it repeatedly. Also, I'm starting to feel perma-tired.

So I'll drop to three sessions per week, but boost the intensity. So, Saturday will be interval day, where I'll try to do about 75% of the work of Westlake. Tuesday will be Westlake A race. Thursday, Leroy TTx2; I'll do the TT, then a second less intense effort over the course. Hopefully with the additional time to rest and recover, I'll gain some endurance.

A Westlake simulation would be, maintain 250-300W with jumps every 2 minutes for 70 minutes.

Tuesday, May 19, 2009

Westlake #3

Blah. That's how I feel after the third outing in the "A" field at Westlake. The weather was beautiful, sunny and warm. The wind was pretty strong and from the east south east and was blasting across the road at turn number 4. (course map)

I started off at the front of the field. The field was big again, and after last week, I learned it is really difficult to move up. From the first lap, attacks were going off like popcorn. Eventually a big group snapped off the front and most of the teams were represented, so the field slowed to a crawl to allow them to get away.

Eventually, the field formed into three groups. I was in the third group, which contained the bulk of the riders. Like last week, I just tired out after a while. Somebody took a huge pull up Ranney Parkway and I just got weary of chasing. I swung off and let the field go by. I was surprised how far forward I was in the group, and how many people were still left.

I'm really tired after this race. But I was only in it for about a half hour. The average power was only 260W. At Leroy I'm averaging way over 300W for 20 minutes. The frequency of the anaerobic efforts is pretty high. Every lap there's a big effort on turn 2, and then on the start/finish straight.

My challenge for the rest of the season will just be to build up my ability to withstand the high intensity efforts for a long time. In the short term, I'll skip riding on Sunday and Monday and see if it helps to be fresh for Tuesday night. I've been feeling pretty wiped out this week.

Monday, May 18, 2009

iBike Gen III Aero First Impressions

I was looking at different power meter options last week. After a couple of days of mulling them over, I decided to plunk down the dough for a new iBike. I was convinced by a comparison between data from the iBike and the Quarq that the iBike is accurate enough for me, and costs a lot less than the other options.

The order handling was top notch. I ordered online from the iBike store, and received the unit a couple of days later in the mail. It was $800 and change. For that you get the iBike computer, a wireless stem mount, a cadence and speed pickup, and a heart rate belt. The hardware to mount the computer is included: zip ties, double sticky, and a couple magnets. The iBike Windows and Mac software is also included. There is a CD that has a trial version of TrainingPeaks in the package. Batteries for all the devices were included. The design thoughtfully uses one readily available battery type. Also there's a USB to serial dongle for the iBike/PC interface.

One minor gripe: No extra zip ties were included. It's pretty easy to screw up the installation of a bike computer and its sensors, so several extras should be included. One other minor gripe, I wish they'd implement the USB/PC interface as a USB mass storage device instead of the serial port converter. Then you'd be able to use it without a custom dongle and without installing drivers.

Since the iBike sensors are wireless, installation was very easy. The design of the mounts is clever and seem like they would attach easily to any fork and to any frame (for the cadence mount). The sensors are sensitive and pickup the magnet from more than a few millimeters away.

The stem mount for the bike computer was also easy to install. I managed to attach it upside down the first time, so I popped it off, scraped off the double sticky, and put it back on the right way in a few minutes. The mount was secure and stable as soon as I tightened the screws. The handlebar mount for the old iBike required a lot more fuss.

The instructions for installations were well written and clear. My only complaint is they should consider consolidating the collection of separate PDF instruction files into a single file. It's a little confusing to have multiple manuals, but really not a big deal. Some readers might prefer the multiple files.

The calibration of the iBike is a multi-step process. Since I've been using one for several years, I'm pretty familiar with the concepts, so it went pretty smoothly. You enter the combined weight of the rider and the bike (and all the stuff that you carry). Then, you calibrate the tilt sensor. Then you do a "coast down" and (new with the iBike Gen III) do a calibration ride. I performed the coast down and calibration ride three times over three days. The first two days, the wind was really strong and gusty, so I was in doubt about the results. The third day, the results converged and were reproducible.

I think the coast down and the calibration ride must be a little intimidating for a new iBike owner. If you buy a new iBike spend some time reading the manual and watching the videos. It will probably take you several tries to get it right.

Once I started to collect data I was pretty stoked at the new iBike application. It provides a clear view of the oodles of information the iBike collects: speed, power, elevation, and hill slope. It also automatically downloads weather data and associates that with your ride! You can edit files: join files, split files, and do all sorts of analysis of the data. You can zoom in on sections of data, like a hill climb. I've yet to scratch the surface of all the things it can do. The application provides a nice summary of the analysis in a text box so you can cut and paste (Rogers Road Hill Climb from Sunday Club Ride):

---------Selection Stats---------
Dist:        0.35 mi (0:02:59)
Energy:      59.9 kJ
Cals Burn:   57.3 kcal
Climbing:     163 ft
Braking:      1.2 kJ (2.0%)
          Min   Avg    Max
Power     184  334.6   526  W
Aero        0    3.2    16  W
Rolling    18   25.3    44  W
Gravity    58  297.8   485  W
Speed     5.0    7.1  12.4  mi/h
Wind      0.0    4.1  10.4  mi/h
Elev      455    544   620  ft
Slope     1.1   8.55  17.5  %
Caden      44   62.2   108  rpm
Aero: 0.229; Fric: 2.48
CdA: 0.353 m^2
Crr: 0.0072
248 lbs; 5/17/2009 2:49 PM
68 degF; 1013 mbar

So far the measured power lines up with past experience. I'll get more real data at the Leroy TT this week. I'm happy with the iBike Aero, I'll post a complete review in a couple of months.



Friday, May 15, 2009

VO2 Max

Stolen from Ray Huang's blog:

VO2 max= 1.8*(P5min*6.12/Kg)+3.5

And for reference:

http://fitness.testing.8m.com/vo2max-test.htm


Thursday, May 14, 2009

Leroy TT #1

My wheel truing stand and spoke tension meter arrived in the UPS van in the early afternoon, so I spent some time before the TT truing my fancy new Dura-Ace carbon/aluminum front wheel. Between Westlake's cracked concrete and the Covered Bridge series railroad tracks crossings, it was knocked around pretty hard. I realized I'd have the wheel in and out of the shop on a regular basis, and would start snapping spokes unless I finally developed some wheel truing skills.

The tension meter worked perfectly. I measured the tension on each side of the wheel, and tagged the high and low tension spokes with sticky book marks, then inspected the wobble of the wheel with a slow spin. No surprises! The wheel was off center where the spoke tension was unbalanced. I gradually adjusted the tension of each high or low tension spoke, measured, and spun. In a few minutes I had it nearly as good as new.

I drove up to Leroy at about 5:30PM, the rain from the early morning had cleared, and it was a beautiful sunny, warm day with a sustained 10 mph wind probably at about 280 degrees on the compass (WNW), right down the finish. I took an easy spin around the course. The tailwind was huge on the outbound section, I barely had to pedal to do 17 mph. There was a little crosswind on the uphill leg to the turn. On the way back, there was a little shelter from the wind except past the substation and the farm field where it was pretty fierce.

I wanted to get a 20 handle on my time and average slightly better power output than last week. I planned to push the pace a little harder on the downhill after the turn, since I was resting a little bit there in prior weeks.

Bill Marut was there along with Larry, Darrel, and another Kevin. Jim handed out the popsicle sticks and I was starting second behind Bill who was on his TT bike. This season, the TT bikes are going first so there's less of a chance of getting caught if you're on a road bike. Bill took off up the road, and I lined up and reset the old bike computer. I've been riding the course every Thursday since March, usually twice per session, so the start is programmed into my legs by now. I hold back on the first rise, then start to accelerate across the field.

It felt pretty easy to go fast with the tailwind, and I was pushing good power. I could feel my heart spooling up as I made my way across the field, and felt like I was holding back a little even though I kept seeing 400W pop up on the meter. I made the turn perfectly and accelerated up the climb. During the last few sessions, I've been trying to peg my effort all the way up the climb, but I tend to crumple a little bit after the first rise, and then make a strong sprint up to the summit. I think next week, I'll hold back a little at the beginning and try to ramp up the power all the way to the top.

As I made the summit, I saw that I'd have to wait a few seconds for a jeep to drive by before I did the turnaround, so I sat up and coasted. Since it's an open course, it's common to be held up by vehicle traffic and you just have to live with it. I've noticed the people that live on the streets like to stop in the middle of the road on a regular basis so you really have to pay attention.

I pushed the pace a little harder down the hill than last week and could feel a little pressure from the wind on my left shoulder. The finish was going to be tough!

The mile marks on the road were repainted this season and I was waiting to see the 2 miles to go mark, which is where I planned to start really hammering. The power meter was showing 400+ all the time as I headed toward 1 mile to go. It was hurting! I felt like I could hold on the the finish, though.

Finally, the fire station sign came into view and I lifted the pace more switching into a fully anaerobic effort. The wind kept me under 30 mph crossing the line, but my finish was still pretty strong. I chalked up a 20:52 (22 mph average) in spite of a small delay from traffic, and averaged 377W. That's my career best power output for 20 minutes, 40 seconds better than last week, and 10 seconds better than my best time so far this season.